Maryland State Inspection Class A Practice Test

These questions are part of the practice quiz. Start practicing

• What is required to check the brakes of a vehicle during inspection?
• What is the inspection outcome for a vehicle that is missing a muffler?
• How much auto repair knowledge is required for an inspector?
• What is the acceptable difference in wheelbase on both sides of a vehicle?
• Under what condition are drum and disc brakes rejected?
• How many jack stands are required at each inspection station?
• What is the allowable play for a 16 inch rim?
• What occurs during the visual inspection phase of a vehicle inspection?
• What must the hood of a vehicle do to pass inspection?
• What is a sign of mechanical damage in brake components?
• What is the minimum height for fog lights from the ground?
• If a tire shows signs of cuts, what is the required action?
• What happens if the critical area of the windshield has any cracks that exceed 1/2 inch?
• What happens if steering performance interferes with the vehicle's handling?
• What is the purpose of conducting regular vehicle inspections?
• What tread depth indicates that a tire has failed?
• Which tool measures tire tread depth at an inspection station?
• What gases can enter the cabin, causing a failure of the floor pan during inspection?
• What is the maximum allowable time for an inspection appointment to be rescheduled?
• What is the recommended length for prybars used to check ball joints?
• What is the requirement for rear seatbelt installation in vehicles?
• What is the maximum height at which fog lights should be mounted?
• For a vehicle with radial tires, what is required regarding the tires?
• What comprises the critical area of the windshield?
• What is required for test equipment used in inspections?
• What is the maximum bumper height for a passenger vehicle according to inspection standards?
• Inspections must be performed at the same station with the same mechanic; what is the consequence if this is not followed?
• What equipment must be present at an inspection station?
• What type of vehicles does Class A exclude?
• Under what condition would alignment be rejected?
• What should be the condition of the windshield wipers during testing?
• What is the maximum allowable play for a 17 inch rim?
• What is the consequence of having tint below the AS1 line?
• What happens if a tool replacement or repair cannot be done within 72 hours?
• What type of vehicles does Class R include?
• How many fog lamps are permitted by law?
• What is the use of AS4 and AS6 glass?
• What should be checked on the gear indicator of an automatic vehicle?
• What condition regarding treadwear can lead to a tire being deemed as failed?
• What must be ensured about the exhaust system during an inspection?
• During vehicle inspection, how is the fuel system assessed?
• What measurement of brake pedal height is acceptable during the inspection?
• For how long must inspection certificates be kept?
• What must be allowed to open and close on the driver side?
• How is steering lash inspected during an automotive inspection?
• What slope should the station surface not exceed?
• What is the allowable steering movement for a 16 inch steering wheel?
• What is the size requirement for a steering wheel during inspection?
• What feature must all vehicles made after May 23rd, 1970 have?
• What causes wire backed linings to fail an inspection?
• Why would a vehicle fail inspection if the vehicle has radial tires?
• For how long is the inspection certificate valid after passing?
• How long must SERO certificates be retained from the certification date?
• What does a "safety recall" indicate in vehicle inspection?
• What is the legal requirement for windshield wipers in Maryland?
• What is a requirement for maintaining the accuracy of inspection tools?
• How do you convert kilometers to miles?
• What type of vehicles does Class C include?
• What is the maximum allowable rust on brake lines during inspection?
• What is the role of the Maryland Motor Vehicle Administration in inspections?
• What is the maximum allowable play for an 18 inch rim?
• What consequence can defective windshield glass have during inspection?
• Where is the dark tint allowed in vehicles?
• Why is the suspension system checked during inspection?
• Which components are primarily inspected during a Maryland State Inspection?
• What action is recommended to inspect for steering binding?
• What is the required functioning condition for headlights during the inspection?
• What condition leads to the failure of riveted brake linings?
• What size crack in the acute area of the windshield will result in a failure?
• What is the maximum tint level allowed in the acute area of the windshield?
• Are drive-on lifts permitted in the inspection bay?
• At what measurement should riveted brake linings still be above the rivets to pass inspection?
• Which class includes trucks, tractors, and buses that weigh over 10,000 lbs?
• How can vehicle owners find a licensed inspection station?
• Which of the following is assessed for signs of wear in the vehicle?
• What is required during a full brake inspection?
• Where may AS2 glass be used?
• Is it acceptable for a vehicle to be without resonators?
• What does Class G vehicles comprise?
• How many convex mirrors are required in each inspection bay?
• To check for binding in the steering, what action should be taken?
• If suspension modifications are needed to prevent contact, what is the result for the vehicle?
• Can modified vehicles pass a state inspection in Maryland?
• What is the maximum allowable movement for rack and pinion steering?
• How frequently must a vehicle in Maryland undergo a State Inspection?
• What is typically assessed during an initial vehicle inspection?
• What is the proper procedure for using arm signals by the driver?
• Which components are evaluated in the braking system?
• What are the consequences of driving a vehicle without a valid inspection in Maryland?
• How should the steering linkage be checked?
• What action may be taken for vehicles found with serious safety defects?
• What should be ensured about the seat belts during vehicle inspections?
• How are brake lights evaluated during a vehicle inspection?
• Which type of mirror needs to be mounted with AS3 glass?
• When are seatbelts required in the front seats of vehicles?
• What type of windows are subject to different glass design standards?
• Which area is excluded from the critical area definition?
• What is NOT included in Class M vehicles?
• Which vehicle category encompasses any trailer, including those with air brakes?
• What is required for tail lights during the Maryland State Inspection?
• What is a re-inspection?
• When is a windshield considered to be acceptable?
• What is the maximum allowable steering movement for an 18 inch steering wheel?
• What is the measurement precision required for a drum micrometer?
• What indicates that vehicle shocks are functioning well?
• What should a technician check for when assessing wheelbase?
• In what situation can tint be applied without restrictions?
• When does a steering wheel fail inspection?
• What is the tint limit allowed for SUVs or trucks?
• What should be done if a vehicle's battery is found to be corrosive?
• What action should be taken if the vehicle rocks more than twice during the shock test?
• What happens if a vehicle fails the State Inspection?
• For which area is AS3 glass permitted?
• What type of vehicles must comply with emissions inspection requirements?
• What types of fluids are checked during a vehicle inspection?
• Where can a visual reinspection for defects be conducted?
• Are motorcycles required to undergo the Maryland State Inspection?
• Where can AS10 be used for application in vehicles?
• What condition of a tire mandates a failure judgment?
• What is the significance of the OBD-II system in emission testing?
• What is considered a non-critical area of the windshield?
• What is defined as the acute area of the windshield?
• What is AS1 used for in vehicle glass?
• Which aspect of the windshield is crucial during the inspection process?
• What is the maximum allowable steering movement for a 16 inch steering wheel?
• What is measured to determine steering wheel lash during the inspection?
• If a U-bolt is not extending beyond the nut after tightening, what happens?
• What is the minimum age requirement for an inspector in Maryland?
• For successful inspections, how should documentation be managed?
• How is severe leakage in shocks determined?
• When should the windshield wipers be rejected during an inspection?
• What part of the steering system must be inspected for damages during an inspection?
• What happens to tint coverage if there is a high mounted brake light in the rear window?
• What is the primary focus of vehicle inspections in terms of safety?
• What happens if more than 2 leaf springs on a 4-leaf spring vehicle are broken?
• What occurs if a vehicle fails an inspection and is repaired at a different facility?
• What does Class F specifically refer to?
• What is required for a vehicle’s ignition system during inspection?
• How does a separation indicated on the sidewall of a tire affect the vehicle's inspection status?
• Which of these measurements is valid for an 18 inch rim?
• What requirement must trucks with a cap or slide-in camper adhere to regarding tailpipes?
• What should be done if the original inspector's license is suspended or revoked?
• For light trucks and vans, what is the stopping distance during the service brake test?
• How can a vehicle owner contest an inspection result?
• What should the inside diameter of the brake drum not exceed?
• When must current brake, ball joint, and tire spec guides be obtained?
• Class T vehicles are characterized by which feature?
• What constitutes a failure if the non-critical area of the windshield contains?
• What tint percentage is permitted for cars?
• For a vehicle with 4 leaf springs, how many can be broken before it fails inspection?
• What documents are necessary for a vehicle undergoing its initial inspection?
• What is typically inspected for safety and compliance in vehicles?
• What condition must the steering linkage meet?
• What aspect of the vehicle's lighting is checked during the inspection?
• What is the required mounting height range for headlights?
• How are safety belts evaluated during the inspection process?
• Which items are classified as "safety items" checked during each inspection?
• What condition necessitates the replacement of a vehicle battery?
• Which class of vehicles includes any combination of Class B and Class C vehicles?
• What is the minimum thickness for regular brake linings to pass inspection?
• What happens if a vehicle has two or more tires of different sizes on the same axle?
• How long should U-bolt length be beyond the nut when tightened?
• From which point should the mounting height of headlights be measured?
• Which of the following vehicles is categorized as Class R?
• What condition must tires meet during inspection?
• What should be checked first during a vehicle inspection?
• What should an inspector look for regarding the windshield condition?
• What must be refunded if a facility license is suspended or revoked?
• Where must a registered mechanic work to be compliant?
• Which condition would be acceptable for brake linings during inspection?
• What effect do engine warning lights have on a vehicle inspection?
• Which of the following is NOT required in the inspection bay?
• What is one common reason for a vehicle failing its inspection?
• For what vehicles is the Maryland State Inspection program applicable?
• What are the mandated operating hours for vehicle inspections?
• According to inspection standards, when should a windshield be failed?
• What is the measurement capability of a disc micrometer?
• How often must tools that require calibration be calibrated?
• What is the requirement for tire pressure during inspection?
• Which of the following indicates a problem with brake discs?
• What does a "passed inspection" signify for the vehicle?
• What is the minimum measurement for pads on disc brakes at their thinnest point?
• What is the purpose of the Maryland State Inspection Program?
• Who is authorized to conduct Maryland State Inspections?
• In case of a tool malfunction, what must be displayed at the inspection station?
• What is the minimum tread depth required on tires for a Maryland State Inspection?
• What is the restriction for using AS14 in a convertible vehicle?
• What is the function of the odometer check during vehicle inspection?
• What must be clear of hazards in the inspection bay?
• What is expected of a mechanic after a vehicle reinspection?
• What indicates a significant problem if seen during the steering wheel inspection?
• What design standard should be inspected on vehicle glass?
• How is the body structure of a vehicle assessed during inspection?
• What information is typically included on an inspection certificate?
• What is the role of the AS designations in vehicle glass?
• What must be the nature of disability controls according to inspection standards?
• If a vehicle has less than 4 leaf springs, how many can be broken?
• Under what condition should the odometer or speedometer fail inspection?
• What type of brake lining is unacceptable if it shows uneven wear?
• What should be checked regarding the vehicle's battery during inspection?
• In what area of the windows are stickers or signs allowed?
• What is a critical factor in checking the brake drum's friction surface?
• If a vehicle is returned for reinspection, what is the protocol?
• How can vehicle owners prepare their vehicle for an inspection?
• What condition leads to the failure of a floor pan during inspection?
• What is the maximum vertical height for a hood scoop bubble before it is considered a failure?
• What must be confirmed about the rearview mirrors during inspection?
• What must be considered regarding a vehicle's exhaust system?
• What is the role of the catalytic converter in a vehicle?
• What is the minimum diameter for each convex mirror?
• What might illumination of a check engine light indicate before an inspection?
• To test the vehicle shocks, what should the inspector do?
• How are turn signals assessed during a state inspection?
• What is the impact of having wiper blade scratches in the critical area of the windshield?
• If a windshield has a combination of two cracks, which size allows it to pass?
• What type of SERO inspection can be conducted without a charge?
• Which type of imperfections should be inspected on the windshield?
• How long should the brake pedal height remain constant during the inspection?
• What is a common consequence of failing a vehicle inspection?
• What must a vehicle owner present during a Maryland State Inspection?
• What must happen if appointments are not honored?
• What must be done if a tool for inspection is found to be out of order?
• Which vehicles are classified under Class M?
• During service brake testing, the inspector should stop the vehicle from what speed?
• How is the emissions control system inspected during a Maryland State Inspection?
• What is a required item in an inspection bay for measuring tire pressure?
• What indicates that a vehicle may be rejected due to shock condition?
• Which category includes passenger vehicles and trucks under 10,000 lbs?
• What does a contaminated friction surface indicate during a brake inspection?
• What should be assured about the windshield during vehicle inspection?
• What is the maximum allowable play in the steering system during an inspection?
• What is the minimum requirement for steering wheel condition during a Maryland state inspection?
• What is the maximum bumper height designated for E class light trucks and MPVs?
• What type of vehicle modifications might lead to failing inspection?
• What measurement capability must a ball joint checker have?